ISIS - Innovative Solutions In Space B.V.

CubeSats in brief
A CubeSat is a type of very small satellite which is based on a standardized unit of mass and volume. The initial basic CubeSat unit measured 10x10x10 centimeter, conforming to specific interfaces for allowing a standardized containerized launch and had a maximum mass of 1 kilogram (the mass was later on increased to 1,33 kilogram). It was quickly realized that such basic CubeSat units could be combined to form slightly larger spacecraft while mostly adhering to the same requirements and constraints. Multiples of the basic CubeSat unit were combined together to establish larger CubeSats. For example, a 1-Unit CubeSat measures one single basic CubeSat unit as described above, while a 3-Unit CubeSat consists of 3 standard CubeSat units stacked together.

The CubeSat concept has become very popular, both in university groups, as well as for researchers, space agencies, governments, and companies.CubeSats offer a fast and affordable way for a wide array of stakeholders to be active in space and allow for a fast innovation cycle.

Satellite

cubesats

CubeSats history
Beginning in 1999, California Polytechnic State University at San Luis Obispo (Cal Poly) and Stanford University developed a very small spacecraft concept to help universities worldwide to enable students and researchers perform space science and exploration. The aim was to come up with a concept that would not only allow university groups to rapidly implement a small space mission, but also to ensure that the chances of being embarked on a space launch as a secondary passenger were maximized, by standardizing interfaces and prohibit or limit design aspects that could be potentially hazardous and would reduce the chances of being allowed to be launch next to larger, more expensive spacecraft.

The CubeSat reference design was proposed in 1999 by professors Jordi Puig-Suari of California Polytechnic State University and Bob Twiggs of Stanford University. The CubeSat as initially proposed did not set out to become a standard; rather, it became a standard over time by a process of emergence, and culminated in a very popular and standardized satellite concept. The first CubeSats were launched in June 2003 on a Rockot launch vehicle.

CubeSat characteristics
Module
Launch
Budget
Parts
Design
Risk
Niche Application
3-Unit CubeSat

ISIS 2U Cubesat

Standard CubeSats
A formal standard for CubeSats is under development at the International Organization for Standardization (ISO). In effect, the latest revision of the CubeSat Design Specification (CDS), as maintained by CalPoly since its creation in 1999 contains the design specifications and requirements that is the de-facto CubeSat standard, complemented with a set of additional requirements applicable mainly to CalPoly’s P-POD CubeSat deployer system and to CubeSat missions in development in the US.
The CDS accurately describes the form and fit of 1-Unit and 3-Unit CubeSats and by means of interpolation intermediate sizes such as 1.5-Unit and 2-Unit CubeSats. For larger CubeSats such as 6-Unit and 12-Unit CubeSats the CDS does not really provide an unambiguous handle. This has led to a number of variants of for instance the 6-Unit CubeSat form factor being in use in parallel. With 6-Unit CubeSats being launched into space for the first time in June 2014, it is expected that a standardization of the 6-Unit size will be established soon based on available 6-Unit Deployment canisters and the subsequent emergence of a de-facto standard form factor.

The standardized mass of a CubeSat also turns out to be less of a standard element across all CubeSats, but is rather driven by the limitations of the specific CubeSat deployer used.

CubeSat requirements and constraints
The applicable requirements and constraints to a particular CubeSat mission is a multi-layered composition of requirements. Depending on the chosen development method and standards, possible additional requirements and constraints may apply.

A number of these requirements cannot be known from the start of the mission development. For instance the launch vehicle and launch campaign specific constraints are only known late in the development, once a launch has been selected and the launch campaign specifics have been agreed with all involved parties.

Therefore, it is common practice to use sets of ‘envelope specifications’ that allow more flexibility during the initial design stages. Once the specific deployer and launch vehicle have been selected, it may be possible for a team to reduce the requirements further to encompass just the remaining candidates.

CubeSat Standard Generic Requirements – lay down the basic constraints for being a CubeSat, mainly form and fit
Deployer Specific Requirements and Constraints – may impose additional constraints such as maximum mass, total envelope, location of possible access hatches, etc
Launch Vehicle Specific Requirements – mainly determine the testing requirements and determine whether specific tests are required or not
Launch Campaign Specific Requirements and Constraints – typically have a programmatic impact, such as latest access to the spacecraft, and impact the options to be allowed to use higher risks system elements (pyrotechnics, propulsion, etc.)
Programmatic and Regulatory Requirements and Constraints – sometimes independent of a specific technical implementation, depending on the sponsor, applicable government agencies, etc.. This includes adherence to national space laws